Banana jack adapter for breadboards

Banana jack adapter for breadboards

“I’ve created this adapter to facilitate the interface between banana plugs and breadboards. It allows you to connect up to four banana plugs on each side of the standard 840 pin breadboard.” - Link

more ...

Parametric Garage Boxes

Parametric Garage Boxes

“This is a box customizer with a roller door just like a garage. You only need to set the width, height and depth of the box and get the files ready to print. The door has been designed with tolerances in joints but i recommend doing a first test with the ‘test.stl’ file, a small piece used for calibration …

more ...

Parametric Lego Robot Wheels

Parametric Lego Robot Wheels

“This is part of a set of customizable Lego compatible robotics components. This post is for parametric Lego compatible WHEELS. (Necessary Treads are a separate Thingy here: https://www.thingiverse.com/thing:2418636) (Thingy’s are separate because each is its own customizer.) Files Included: An openscad file for generating any diameter of stackable Lego wheel with one of 5 …

more ...

Parametric Servo Gripper Lego Brick Set

Parametric Servo Gripper Lego Brick Set

“This is part of a set of customizable Lego compatible robotics components. This post is for various Lego compatible 9g servo mounts. This fits either the popular SG90 or the FS90R (continuous) servos. Files Included: 6 differently oriented servo mounts. An openscad file for customizing the gripper/flag. (The flag is intended to be an accessory for a mini-sumo robot …

more ...

Customizable Sanding Stick

Customizable Sanding Stick

“I like the idea of the Sanding stick by workshopbob, but I don’t want to buy some hex screws. So I’ve created this thing, where you can customize your sanding stick, that will automatically include the needed printable screws.” - Link

more ...

OpenScad Micro Servo Robot Arm Remix using MG90 Servo’s

OpenScad Micro Servo Robot Arm Remix using MG90 Servo’s

“My MG90s servos are 3mm taller than SG90’s so I hacked the scad file to accommodate the taller servo’s. Update: Added zip file with component parts converted to STEP format for SolidWorks using FreeCad. The Gripper Gear would not import so it’s not included.” - Link

more ...

Parametric Music Box

Parametric Music Box

“This is a 100% printed customizable music box! Only 3D printed parts are used in the design and it can be assembled and disassembled via printed snapping mechanisms. The project originated when a friend of mine said that he’d only be interested in 3D printing once he can print a music box ;)” - Link

more ...

Chip-E - RobotGeek Biped

Chip-E - RobotGeek Biped

“Chip-E is RobotGeek’s first 3D printable robot kit that you can build yourself! Powered by the RGS-13 servos and the RobotGeek Geekduino and Sensor Shield components Chip-E is a cute and lovable walking companion that you can print at home, with a friend or through a printing service. Open source design and programming allow you to expand its …

more ...

Peg board round cable holder

Peg board round cable holder

“A pegboard holder for electronic test leads and cables. This cable holder fits to the standard 1 inch spaced pegboards. The OpenSCAD file is included in case you want to modify the design.” - Link

more ...

Drawers for small components

Drawers for small components

“I needed some drawers for organizing resistors, capacitors and other small components. I wanted the resistor compartments to have cut-outs on the dividers to make it easier to get the resistors out with fat fingers, and I wanted a lot of customizability in the drawer divider organization. You can also customize the dimensions heavily. The design is optimized for minimal …

more ...